Japanese swords, equipment, custom knives and more. Our focus is supporting students of the sword and providing high quality functional swords and a full line of accessories. If you study iaido, battodo, kenjutsu, or any other form of Japanese swordsmanship - this is the place for you.
Sharpening is not a cosmetic polish but does affect the whole surface of the blade! It is not intended to make the sword look good. It makes the sword cut better. One of the basic requirements for Tameshigiri is a sharp well shaped katana edge. The blade surface must be polished (not cosmetic) and the geometry correct. Most practitioners make the mistake of trying to sharpen their own blades with products designed for knifes. It is the whole surface and not just the edge that makes the katana cut well.
We can optimize the edge for soft or hard targets. Soft targets include tatami and beach mats. Bamboo is considered a hard target. We use a series of Japanese water stones and diamond polishing abrasives ranging from 80 to 10,000 grit to put a razor edge and polished surface on your katana. A standard sharpening only sharpens about 14 to 16 inches of the blade which is used for cutting. This is normally the only part that becomes dull. We will also sharpen the kissaki.
We also offer a sharpening polish that removes all of the diagonal scratches from the water stones and continues the polish to 40,000 grit. While this does not improve the cutting ability of the sword, it does make it look much better. A Hybrid Polish includes cleaning up all surfaces of the blade and enhancement of the hamon. This will make your sword like new.
The katana should have a removable tsuka. Please email us if you wish to sharpen a sword with the tsuka permanently attached. We will remove the tsuka and straighten the blade as part of the normal process. Swords should be shipped with saya and fittings to protect the blade. The tsuba can be removed to reduce the dimensions of the sword, but the sword should be shipped with the tsuka and mekugi peg to keep the blade from being forced into the saya and splitting it.
Bent swords are a standard part of tameshigiri training. Shinken are designed to bend and not break. As long as the hardened edge has not cracked, the sword can be straightened. We will use wood straightening jigs to get bends and twists out of your swords.
A standard sharpening (monouchi only) sharpens about 14 to 16 inches of the katana which is used for cutting (including the kissaki). This is normally the only part that becomes dull. The sharpened half of the blade may vary from the rest of the blade and there may be some faint scratches left from coarser stones.
A whole blade sharpening includes the cutting edge back to the habaki. This type of sharpening is useful for dodan cutting which uses the entire length of the blade. It also produces a uniform finish over the entire length of the blade but there may be some faint scratches left from coarser stones.
A sharpening polish sharpens the whole blade including the cutting edge back to the habaki. This type of sharpening produces a uniform finish over the entire length of the blade. It also refines the finish further than the standard and whole blade sharpening using abrasives going to 1 micron.
A hybrid polish adds clean-up of all the blade surfaces and cosmetic enhancement to the hamon. It sharpens the whole blade and polishes all surfaces using abrasives going to 1 micron. It also includes a light chemical etch to further bring out the hamon (hardened edge).
Chips and nicks in the blade can be removed as long as they do not go past the hamon. Chip and nick removal over 1/64th of an inch are an additional charge to standard and whole blade sharpening. Chips and nicks are removed by reshaping the blade on a slow speed wet grinder before sharpening.
Additional Edge Reshaping
We offer a full line of training equipment and services. We are a one stop shop for your training and collecting needs. We offer training, sharpening, and repair in addition to a full line of iaito and shinken. Buy from a company that can do more than just ship you a sword.
Discounted Prices (normally 15% to 40% off of retail) 90 Day Money Back Guarantee, Lifetime 1/2 Price Sharpening and Repair on any Katana.
When one sword is just not enough - Nihonzashi
Sherry & Mike Femal,
Sherry and Mike started Nihonzashi in 2006 so their students of Toyama Ryu would have a consistent supply of uniforms, swords and tatami mats. We have enjoyed growing the business to what it is today and are proud to be known worldwide for our custom products and services. Sherry and Mike created and custom make all of the gekken swords we ship around the world. Also, Mike is fulfiling his dream of expanding his custom weapons to include knives. We look forward to what the future brings and what new creations are on the horizon.
5980 66th Street North, Suite M, St Petersburg, FL 33709
Monday — Friday
10:00am to 5:00pm